| | |
| 0410 | Repair strength of hypoallergenic denture base materials
P. PFEIFFER, and N. AN, University of Cologne, Germany |
| 0411 | Impact strength, fracture toughness and brittleness of nine denture acrylics
W. WACHTER1, O. THEWS2, G. ZAPPINI1, A. KAMMANN1, S. SBICEGO1, and H.-F. KAPPERT1, 1Ivoclar Vivadent AG, Schaan, Liechtenstein, 2University of Applied Sciences, Osnabruck, Germany |
| 0412 | Shrinkage stress of new experimental low shrinkage resin composites
A. SCHATTENBERG, G.R. MEYER, B. WILLERSHAUSEN, and C.-P. ERNST, Johannes Gutenberg University, Mainz, Germany |
| 0413 | Viscosity of Composite Cores compared at ambient and oral temperature
G.D. DIXON1, P.C. MOON2, J.M. CARTER1, and C.N. BROOKS2, 1Virginia Commonwealth University, Richmond, USA, 2Virginia Commonwealth University VCU/MCV, Richmond, USA |
| 0414 | Long-term Viscoelasticity of Soft Lining Materials
M. NAKAYAMA, T. KUMAGAI, and S. AKAHANE, GC Corporation, Tokyo, Japan |
| 0415 | Manual vs. Electric Toothbrush Abrasion of Resin-Modified Glass Ionomer
K. PELKEY1, K.S. VANDEWALLE1, and J. LINDEMUTH2, 1USAF, Lackland AFB, TX, USA, 2USAF, Travis AFB, CA, USA |
| 0416 | Abrasion Wear Results of Sealant Materials After Storage in Water
M.L. CANNON, Northwestern University, Long Grove, IL, USA, R. NUNEZ, Bisco Dental, Schaumburg, IL, USA, and A.E.M. VIEIRA, Sao Paulo State University, Aracatuba, Brazil |
| 0417 | Three-body Wear of Fissure Sealants
C. MÜRNSEER1, M. ROSENTRITT2, M. BEHR3, and G. HANDEL2, 1University Medical Center Regensburg, Germany, 2University of Regensburg, Germany, 3Zentrum fur Zahn, Mund, und Kieferheilkunde, Regensburg, Germany |
| 0418 | Physical Properties of Bisco Experimental Temporary Filling Material
Y. WANG, R. YIN, D. SHIN, and B. SUH, Bisco, Inc, Schaumburg, IL, USA |
| 0419 | Optimizing the properties of a low shrinkage two monomer blend
J. COLLETTE, T. JARDINE, H.L. CARDENAS, B.R. FURMAN, N. SATSANGI, and B.K. NORLING, University of Texas - San Antonio / Health Science Ctr, USA |
| 0420 | Dimensional Stability and Mechanical Properties of Alginate Hydrocolloid Impression Materials
G.A. KRISHNAN, R. YAPP, and J.M. POWERS, Dental Consultants Inc, Ann Arbor, MI, USA |
| 0421 | In-Vitro Wear of a Heat Cured Indirect Composite Resin
V. BUI, A. KOBASHIGAWA, and E. SHELLARD, Kerr Corporation, Orange, CA, USA |
| 0422 | Efficacy of 5- and 10-Second High Intensity Led Exposures
F.A. RUEGGEBERG, J. RAUSCH, and A. OXFORD, Medical College of Georgia, Augusta, USA |
| 0423 | Dimensional stability and mechanical properties of alginate substitutes and alginate
G.A. KRISHNAN, R.A. YAPP, and J.M. POWERS, Dental Consultants Inc, Ann Arbor, MI, USA |
| 0424 | Three Body in-Vitro Wear Test Method
A. KOBASHIGAWA, V. BUI, and E. SHELLARD, Kerr Corporation, Orange, CA, USA |
|