| | |
| 2660 |
3:45 PM | Surface Wettability of Saliva and Blood Plasma During Setting of Impression Materials
M.S. KIM1, B. REUSCH2, H. HOFFMANN2, E.H. DOHERTY1, and G. KUGEL1, 1Tufts University, Boston, MA, USA, 23M ESPE, Seefeld, Germany |
| 2661 |
4:00 PM | Dimensional Change and Curing Characteristics of Temporary Inlay & Onlay Materials
E. NGUYEN, D.X. XIE, and E. SHELLARD, Kerr Corporation, Orange, CA, USA |
| 2662 |
4:15 PM | Accuracy of two elastomeric impression materials in transferring Paragon® dental implants: a three-dimensional analysis
D.A. BRAVO-CAVICCHIOLI, University of Puerto Rico, School of Dentistry, USA and Universidad de Talca, Chile, A.R. ELÍAS-BONETA, University of Puerto Rico, School of Dentistry, Rio Piedras, USA, and W.J. PSOTER, New York University, USA |
| 2663 |
4:30 PM | Effects of Viscosity and Time on DMA of Two Elastomers
J.M. VICKERY, The University of Nebraska Medical Center College of Dentistry, Lincoln, USA, W.A. BRANTLEY, The Ohio State University College of Dentistry, Columbus, USA, and T.H. GRENTZER, Ashland Specialty Chemical Company, Dublin, OH, USA |
| 2664 |
4:45 PM | A comparison of surface quality of provisional crowns after chairside polish
A. BOECKLER, Martin Luther University, Halle / Saale, Germany, and J. SETZ, Martin Luther University, Halle, Germany |
| 2665 |
5:00 PM | Effect of Glass/Epoxy Framework on the Fracture Resistance of Direct Provisionals
P. BALDISSARA, L. BOSCHINI, A. PULGA, and S. MALFERRARI, University of Bologna, BOLOGNA, Italy |
| 2666 |
5:15 PM | Physical Propeties of Two Chemically-Cured Core Materials
M.A. LATTA, M.N. KELSEY, and W.T. NAUGHTON, Creighton University School of Dentistry, Omaha, NE, USA |
| 2667 |
5:30 PM | Mechanical Properties of Polysulfide Impression Materials
L. HUYNH, D.X. XIE, and E. SHELLARD, Kerr Corporation, Orange, CA, USA |
| 2668 |
5:45 PM | Physical Properties of Resin-Based Core Materials
T.T. NGUYEN1, A. MSZYCA2, X. QIAN1, and E. SHELLARD1, 1Kerr Corporation, Orange, CA, USA, 2KERR Corporation, Orange, CA, USA |
| 2669 |
6:00 PM | Comparison of Failure Loads of Prefabricated Posterior Composite Crowns to Posterior Composite Strip Crowns
J. STARKEY1, P. SCHNEIDER2, N. SARKAR2, C. DUMMETT2, R. MUSSELMAN2, D. GARDINER2, and M. WINKLER, Jr.2, 1Louisiana State University School of Dentistry, Albuquerque, NM, USA, 2Louisiana State University School of Dentistry, New Orleans, USA |
| 2670 |
6:15 PM | Fracture toughness and flexural strength of various core materials
S.G. AHN1, H.X. BERGE2, and J.A. SORENSEN2, 1Chonbuk national university, chonju, South Korea, 2Oregon Health & Science University, portland, USA |
| 2671 |
6:30 PM | Effect of an inert filler on physical properties of ethyl/isobutyl methacrylate
J. KIM, J. ASTROTH, and J.W. STANSBURY, University of Colorado Health Sciences Center, Denver, USA |
| 2672 |
6:45 PM | Effect of Polymerization Temperature on the Transverse Strength of Autopolymerizing Acrylic Resin
S. KIM, USC School of Dentistry, Los Angeles, CA, USA, K.T. OCHIAI, UCLA School of Dentistry, Los Angeles, USA, A.A. CAPUTO, UCLA School of Dentistry, Los Angeles, CA, USA, and T. DONOVAN, USC School of Dentistry, LA, CA, USA |
|